Votre recherche
Résultats 6 ressources
-
When the shield tunnel passes through the gas-bearing strata, gas and water leakage may occur depending on the sealing performance of the segment joints. This process involves the complex multiphase seepage flow phenomenon in unsaturated soil. In this study, a fully coupled solid-liquid-gas model of the GIL Utility Tunnel was established to investigate the influence of the high-pressure gas on the mechanical properties of the tunnel segments and joints. The constitutive model of the Extended Barcelona Basic Model was implemented to simulate the effect of the seepage process on soil deformation. The results show that significant upward displacement occurred in the gas reservoir and its overlying strata, and the maximum displacement reached 30 mm. In addition, during the leakage of the gas and the water, an increase in the average soil effective stress was observed. It would induce a reduction in the suction and expansion of the yield surface. The tunnel tended to be stable from 20 years onwards, thus the soil deformation due to the water leakage only occurred at the early stage. In addition, the joint opening under the most unfavorable internal force combination was 0.69 mm, and the corresponding bolt stress was 119.5 MPa, which is below the yield limit. The results of this study help to understand the influence of high-pressure gas on tunnel safety and the sealing performance of the joints.
-
The recognition of the geomechanical properties of methane hydrate-bearing soil (MHBS) is crucial to exploring energy resources. The paper presents the mechanical properties of a pore-filled MHBS at a critical state using the distinct element method (DEM). The pore-filled MHBS was simulated as cemented MH agglomerates to fill the soil pores at varying levels of methane hydration (MH) saturation. A group of triaxial compression (TC) tests were conducted, subjecting MHBS samples to varying effective confining pressures (ECPs). The mechanical behaviors of a pore-filled MHBS were analyzed, as it experienced significant strains leading to a critical state. The findings reveal that the proposed DEM successfully captures the qualitative geomechanical properties of MHBS. As MH saturation increases, the shear strength of MHBS generally rises. Moreover, higher ECPs result in increased shear strength and volumetric contraction. The peak shear strength of MHBS increases with rising MH saturation, while the residual deviator stress remains mainly unchanged at a critical state. There is a good correlation between fabric changes of the MHBS with variations in principal stresses and principal strains. With increasing axial strain, the coordination number (CN) and mechanical coordination number (MCN) increase to peak values as the values of MH saturation and ECPs increase, and reach a stable value at a larger axial strain.
-
The production of natural gas hydrates will change the cementation strength, porosity, and effective stress in the stratum, which may lead to engineering and geological disasters. Sand production is a phenomenon where sand particles are carried out of the reservoir along with fluids during gas extraction, posing challenges to safe and sustainable production. This study explored the mechanism of fine particle migration in multiphase flow by a microscopic visualization test device. The device can inject a gas–liquid–solid phase at the same time and allow real-time observation. Experimental tests on fine particle migration of single- and two-phase fluid flow were carried out considering different conditions, i.e., fine particle concentration, fine particle size, fluid flow rate, and gas–liquid ratio. The results show that in single-phase fluid flow, the original gas will gradually dissolve in the liquid phase, and finally stay in the test device as bubbles, which can change the pore structures, resulting in the accumulation of fine particles at the gas–liquid interface. In two-phase fluid flow with mixed gas–water fluids, there are two flow modes of gas–liquid flow: mixed flow and separated flow. The interfacial tension at the gas–liquid interface can effectively migrate fine particles when the gas–liquid flows alternately and the sand production rate further increases as the gas–liquid ratio increases. In addition, changes in the concentration of fine particles, particle size, fluid flow rate, and the gas–liquid ratio will affect the migration of fine particles, leading to differences in the final sand production.
-
The degradation of soil bonding, which can be described by the evolution of bond degradation variables, is essential in the constitutive modeling of cemented soils. A degradation variable with a value of 0/1.0 indicates that the applied stress is completely sustained by bonded particles/unbounded grains. The discrete element method (DEM) was used for cemented soils to analyze the bond degradation evolution and to evaluate the degradation variables at the contact scale. Numerical cemented soil samples with different bonding strengths were first prepared using an advanced contact model (CM). Constant stress ratio compression, one-dimensional compression, conventional triaxial tests (CTTs), and true triaxial tests (TTTs) were then implemented for the numerical samples. After that, the numerical results were adopted to investigate the evolution of the bond degradation variables BN and B0. In the triaxial tests, B0 evolves to be near to or larger than BN due to shearing, which indicates that shearing increases the bearing rate of bond contacts. Finally, an approximate stress-path-independent bond degradation variable Bσ was developed. The evolution of Bσ with the equivalent plastic strain can be effectively described by an exponential function and a hyperbolic function.
-
To study the mechanical and cracking modes of anhydrite rock under the freeze–thaw weathering process, the physico-mechanical characteristics and morphology evolutions of anhydrite samples were determined by a series of laboratory tests. Then, a numerical simulation model was established through the PFC2D program, and the types and number of cracks during the uniaxial compression conditions were analyzed. Finally, the distribution of maximum principal stress and shear stress was revealed. The results indicate that as the number of freeze–thaw cycles increases, there is a growth in the mass loss rate and macroscopic damage variables while the uniaxial compression strength and elastic modulus decrease exponentially. Under uniaxial compression stress, the proportion of tensile cracks in the anhydrite model is the highest, followed by tensile shear cracks and compressive shear cracks. As the number of freeze–thaw cycles increases, the proportion of tensile cracks increases exponentially, while the proportion of tensile shear cracks and compressive shear cracks decreases exponentially. Furtherly, it is found that the maximum principal stress and maximum shear stress extreme values decrease exponentially with the increase of freeze–thaw cycles. For example, after 120 cycles, the maximum shear stress at the peak stress point decreased by 47.3%. The research results will promote the comprehension of anhydrite rock geotechnical engineering disaster mechanisms in cold regions.