Votre recherche

Abstract Floods are the most common and threatening natural risk for many countries in the world. Flood risk mapping is therefore of great importance for managing socio-economic and environmental impacts. Several researchers have proposed low-complexity and cost-effective flood mapping solutions that are useful for data scarce environments or at large-scale. Among these approaches, a line of recent research focuses on hydrogeomorphic methods that, due to digital elevation models (DEMs), exploit the causality between past flood events and the hydraulic geometry of floodplains. This study aims to compare the use of freely-available DEMs to support an advanced hydrogeomorphic method, Geomorphic Flood Index (GFI), to map flood-prone areas of the Basento River basin (Italy). The five selected DEMs are obtained from different sources, are characterized by different resolutions, spatial coverage, acquisition process, processing and validation, etc., and include: (i) HydroSHEDS v.1.1 (resolution 3 arc-seconds), hydrologically conditioned, derived primarily from STRM (NASA) and characterized by global coverage; (ii) ASTER GDEM v.3 with a res. of around 30 m (source: METI and NASA) and global coverage; (iii) EU-DEM v. 1.1 (res. 1 arc-second), Pan-European and combining SRTM and ASTER GDEM, customized to obtain a consistency with the EU-Hydro and screened to remove artefacts (source: Copernicus Land Monitoring Service); (iv) TinItaly DEM v. 1.1, (res. 10 m-cell size grid) and produced and distributed by INGV with coverage of the entire Italian territory; (v) Laser Scanner DEM with high resolution (5 m cell size grid) produced on the basis of Ground e Model Keypoint and available as part of the RSDI geoportal of the Basilicata Region with coverage at the regional administrative level. The effects of DEMs on the performance of the GFI calibration on the main reach of the Basento River, and its validation on one of its mountain tributaries (Gallitello Creek), were evaluated with widely accepted statistical metrics, i.e., the Area Under the Receiver Operating Characteristics (ROC) curve (AUC), Accuracy, Sensitivity and Specificity. Results confirmed the merits of the GFI in flood mapping using simple watershed characteristics and showed high Accuracy (AUC reached a value over 0.9 in all simulations) and low dependency on changes in the adopted DEMs and standard flood maps (1D and 2D hydraulic models or three return periods). The EU-DEM was identified as the most suitable data source for supporting GFI mapping with an AUC > 0.97 in the calibration phase for the main river reach. This may be due in part to its appropriate resolution for hydrological application but was also due to its customized pre-processing that supported an optimal description of the river network morphology. Indeed, EU-DEM obtained the highest performances (e.g., Accuracy around 98%) even in the validation phase where better results were expected from the high-resolution DEM (due to the very small size of Gallitello Creek cross-sections). For other DEMs, GFI generally showed an increase in metrics performance when, in the calibration phase, it neglected the floodplains of the river delta, where the standard flood map is produced using a 2D hydraulic model. However, if the DEMs were hydrologically conditioned with a relatively simple algorithm that forced the stream flow in the main river network, the GFI could be applied to the whole Basento watershed, including the delta, with a similar performance.

To simulate the dynamics of two-dimensional dam-break flow on a dry horizontal bed, we use a smoothed particle hydrodynamics model implementing two advanced boundary treatment techniques: (i) a semi-analytical approach, based on the computation of volume integrals within the truncated portions of the kernel supports at boundaries and (ii) an extension of the ghost-particle boundary method for mobile boundaries, adapted to free-slip conditions. The trends of the free surface along the channel, and of the impact wave pressures on the downstream vertical wall, were first validated against an experimental case study and then compared with other numerical solutions. The two boundary treatment schemes accurately predicted the overall shape of the primary wave front advancing along the dry bed until its impact with the downstream vertical wall. Compared to data from numerical models in the literature, the present results showed a closer fit to an experimental secondary wave, reflected by the downstream wall and characterized by complex vortex structures. The results showed the reliability of both the proposed boundary condition schemes in resolving violent wave breaking and impact events of a practical dam-break application, producing smooth pressure fields and accurately predicting pressure and water level peaks.

Mapping the delineation of areas that are flooded due to water control infrastructure failure is a critical issue. Practical difficulties often present challenges to the accurate and effective analysis of dam-break hazard areas. Such studies are expensive, lengthy, and require large volumes of incoming data and refined technical skills. The creation of cost-efficient geospatial tools provides rapid and inexpensive estimates of instantaneous dam-break (due to structural failure) flooded areas that complement, but do not replace, the results of hydrodynamic simulations. The current study implements a Geographic Information System (GIS) based method that can provide useful information regarding the delineation of dam-break flood-prone areas in both data-scarce environments and transboundary regions, in the absence of detailed studies. Moreover, the proposed tool enables, without advanced technical skills, the analysis of a wide number of case studies that support the prioritization of interventions, or, in emergency situations, the simulation of numerous initial hypotheses (e.g., the modification of initial water level/volume in the case of limited dam functionality), without incurring high computational time. The proposed model is based on the commonly available data for masonry dams, i.e., dam geometry (e.g., reservoir capacity, dam height, and crest length), and a Digital Elevation Model. The model allows for rapid and cost-effective dam-break hazard mapping by evaluating three components: (i) the dam-failure discharge hydrograph, (ii) the propagation of the flood, and (iii) the delineation of flood-prone areas. The tool exhibited high accuracy and reliability in the identification of hypothetical dam-break flood-prone areas when compared to the results of traditional hydrodynamic approaches, as applied to a dam in Basilicata (Southern Italy). In particular, the over- and under-estimation rates of the proposed tool, for the San Giuliano dam, Basilicata, were evaluated by comparing its outputs with flood inundation maps that were obtained by two traditional methods whil using a one-dimensional and a two-dimensional propagation model, resulting in a specificity value of roughly 90%. These results confirm that most parts of the flood map were correctly classified as flooded by the proposed GIS model. A sensitivity value of over 75% confirms that several zones were also correctly identified as non-flooded. Moreover, the overall effectiveness and reliability of the proposed model were evaluated, for the Gleno Dam (located in the Central Italian Alps), by comparing the results of literature studies concerning the application of monodimensional numerical models and the extent of the flooded area reconstructed by the available historical information, obtaining an accuracy of around 94%. Finally, the computational efficiency of the proposed tool was tested on a demonstrative application of 250 Italian arch and gravity dams. The results, when carried out using a PC, Pentium Intel Core i5 Processor CPU 3.2 GHz, 8 GB RAM, required about 73 min, showing the potential of such a tool applied to dam-break flood mapping for a large number of dams.

Large-scale flood risk assessment is essential in supporting national and global policies, emergency operations and land-use management. The present study proposes a cost-efficient method for the large-scale mapping of direct economic flood damage in data-scarce environments. The proposed framework consists of three main stages: (i) deriving a water depth map through a geomorphic method based on a supervised linear binary classification; (ii) generating an exposure land-use map developed from multi-spectral Landsat 8 satellite images using a machine-learning classification algorithm; and (iii) performing a flood damage assessment using a GIS tool, based on the vulnerability (depth–damage) curves method. The proposed integrated method was applied over the entire country of Romania (including minor order basins) for a 100-year return time at 30-m resolution. The results showed how the description of flood risk may especially benefit from the ability of the proposed cost-efficient model to carry out large-scale analyses in data-scarce environments. This approach may help in performing and updating risk assessments and management, taking into account the temporal and spatial changes in hazard, exposure, and vulnerability.